Guide

Megger MFT-X1 app with Bluetooth: what Certio reads by camera and what the beta link does

How Certio gets readings off a Megger MFT-X1 into the schedule of test results: a camera read of the tester screen on the paid plans, and a Bluetooth link that is in beta. What each one does, what it does not do yet, and what to do when it does not connect.

Published 17 November 2026 · Updated 17 November 2026 · Certio Software Ltd

If you test with a Megger MFT-X1, the slowest part of an EICR is no longer the testing. It is reading 30 circuits of results off the instrument and typing them into the schedule, twice if you wrote them on paper first. Certio gives you two ways to skip the typing with an MFT-X1: a camera read of the tester screen, which is on the Starter and Pro plans, and a Bluetooth link to the MFT-X1, which is in the app but labelled beta. This page says plainly what each does today, what it does not do yet, and what to do when the link will not connect. We would rather you knew the limits before you buy than found them in a plant room.

Key takeaways
  • The camera read is the everyday route: select a cell, point the phone at the MFT-X1 screen, confirm the value. Starter and Pro plans.
  • The Bluetooth link is in beta: connect from Tester link or the Pair MFT chip on the grid, press Save on the tester, tap the offered reading into place.
  • The link fills insulation, continuity, ring final and Zs cells, and refuses a reading whose unit does not match an insulation or resistance cell. RCD trip times are mapped but not yet verified in the field.
  • It is MFT-X1 only. Older Megger models and other brands may read by camera, but only the MFT-X1 has been tested.
  • The judgement is yours. The app never decides whether a reading is Ze or Zs, which circuit it belongs to, or whether it passes; you choose the cell and confirm the value.

What the MFT-X1 can do that older testers cannot

The MFT-X1 is Megger's current multifunction tester and it uses Bluetooth Low Energy, where the older MFT1700 and MFT1800 series used classic Bluetooth or had no radio at all. That matters for an app in two ways. First, it works with both iPhone and Android, where classic Bluetooth testers were Android-only. Second, it needs no pairing in the phone's settings: the app finds the tester, you tap it, and you are connected. Megger's own companion software for the X1 is CertSuite; Certio is an independent app and Megger has not endorsed it. Our guide What Is a Multifunction Tester (MFT)? covers the instrument itself, the BS EN 61557 requirements and what an assessor will ask about calibration.

The camera read: what Certio reads from the screen

This is the route most people use. It was built and tested on the MFT-X1; other testers with a readable display may read by camera, but they are untested, so treat that as a bonus rather than a promise.

  1. Open the schedule of test results in the app and select the cell you are about to fill: say column 21, R1+R2, on circuit 4.
  2. Run the test on the MFT-X1 and leave the reading on the screen.
  3. Tap the camera, point it at the display and hold steady. The app reads the number and the unit and offers it for the cell.
  4. Confirm, and the grid moves to the next cell.

Two rules keep this honest. The app only reads a stable number that is plainly on an instrument display; it does not guess from a blurred frame, and if it cannot read the screen it says so and you type the value. And it never decides whether a loop reading is Ze or Zs from the picture, because they look the same on the screen; the cell you selected decides where the reading goes. The same read works for insulation resistance in megohms, continuity in ohms, Zs and RCD trip times, and for the PAT tester screen on a PAT record.

The camera read is an AI feature, so it is on the Starter and Pro plans, with a monthly allowance that is sized for a solo electrician's boards on Starter and much larger on Pro. The Free plan has no AI features; the schedule grid and the A4:2026 forms are there, with the readings typed.

The Bluetooth link (beta): what it does today

The link is in the app now, in the Toolbox under "Tester link (beta)", and as a "Pair MFT" chip at the top of the schedule grid.

  1. Turn Bluetooth on in the MFT-X1's settings and on the phone.
  2. Tap Pair MFT on the grid, or open Tester link, and tap Scan for tester. The MFT-X1 appears by name; tap it to connect. No pairing in the phone's settings is needed.
  3. Select the cell on the grid, run the test, and press Save on the tester when the reading is on the screen.
  4. The reading arrives in the app and is offered against the selected cell. Tap it and the cell fills; the grid moves on.

The link recognises the MFT-X1's saved-result message and fills insulation resistance (MΩ), continuity (R1+R2, R2, and the ring final r1, rn and r2, all in Ω) and earth fault loop impedance Zs (Ω); those are the readings that have been proven on a real tester. RCD trip times (ms) are mapped in the link but have not yet been verified in the field, so use the camera read for column 28 until they have. Before it fills an insulation or resistance cell the link checks the unit of the reading: a volts record, such as the test voltage on an insulation test, never fills a resistance column, and a negative or unreadable value is shown to you rather than written anywhere. The cell you selected decides where an ohms reading goes, so select the right cell before you press Save. It also understands the tester's "send results" transfer, which carries the paired fault-current record of a loop test.

What the beta does not do yet

We call it beta for plain reasons, and you should know them before you rely on it.

  • MFT-X1 only. The MFT1741, MFT1835 and similar use a different radio and are not supported. The MFT1711 and MFT1721 have no radio. Kewtech, Metrel and Fluke testers are not supported over Bluetooth. All of them may read by camera, but the camera read has only been tested on the MFT-X1.
  • Proven on a limited set of testers and firmware. Megger does not publish the X1's Bluetooth protocol, so the link was built by capturing what the tester sends. It has worked reliably on the testers and firmware versions we have tested; a future firmware update could change what the tester sends, and if it does, the app will show the raw capture rather than fill a cell wrongly.
  • Foreground only. Capture happens while the app is open on the screen. Switch to another app and a Save press will not be captured.
  • One reading at a time, into the cell you chose. The link does not sort results into circuits for you from the tester's own numbering. You pick the cell; the tester provides the number.
  • No Zdb, Ipf or Ze through the link. Those board-level figures are entered on the board details screen.
  • No bulk download of a day's stored results. Press Save after each test and tap the offer.

If any of those is a deal-breaker for you, the camera read is the better route today, and the Bluetooth link will keep improving as more testers go through it.

When it will not connect

Most connection problems are one of four things.

Symptom Likely cause What to do
Tester does not appear in the scan Bluetooth off on the tester or phone, or the tester is in a mode that does not advertise Check both, press the tester's Bluetooth key, scan again
Connects, then nothing arrives on Save App not in the foreground, or you pressed Save before the reading settled Keep the app open, wait for the reading to hold, press Save once
Reading arrives but is cut short or wrong The link negotiated a small packet size on connect Disconnect and reconnect from Tester link so it renegotiates
Tester shows "Failed to send" The tester tried a transfer the app did not acknowledge in time Ignore it for the Save push; the per-test Save route still works

If none of that fixes it, use the camera read for the job and, from the Tester link screen, share a capture to support@certio.uk with a note of what the tester displayed. Those captures are how the beta improves.

Does it pass an assessment?

The scheme assessor cares about the instrument, its calibration and your results, not how the number got from the display to the form. Certio prints the instrument serial number from your calibration settings on every certificate, and the certificate itself is laid out to the BS 7671:2018+A4:2026 model forms. What an assessor will not accept is a reading in the wrong column or a Zs compared with the wrong limit, which is exactly what the unit check and the Chapter 41 limits on the grid are there to prevent. Column by column, the schedule is explained in How to Fill In a Schedule of Test Results.

What it costs

The camera read and the Bluetooth link are on the Starter plan at £4.99 a month and the Pro plan at £9.99 a month, charged when you sign up, cancel any time, nothing added at checkout. The Free plan is £0 with no card and gives you the same certificates with the readings typed. For comparison, iCertifi's Test Vision photographs a meter display on its paid plans, and Tradecert's website lists AI import of test results but no Bluetooth tester connection; Best EICR app UK 2026 has the side-by-side.

Download Certio Certs on the App Store Get it on Google Play Get Starter · £4.99/mo

Megger and MFT are trade marks of Megger Group Limited. Certio is an independent product and is not affiliated with or endorsed by Megger.

How Certio helps

Certio produces the EICR, EIC, Minor Works certificate and PAT records on the BS 7671 model forms and turns them into branded PDFs. Photograph the consumer unit and the circuit schedule drafts itself; point the phone camera at a Megger MFT-X1 and the reading goes straight into the schedule of test results. Suggested observation wording with the regulation reference is there for you to check and confirm. The judgement stays yours; the typing goes. Starter is £4.99 a month, charged when you sign up.

Straight answers

Questions

Does Certio connect to the Megger MFT-X1 over Bluetooth?
Yes, as a beta. The MFT-X1 uses Bluetooth Low Energy and needs no pairing in the phone's settings. In Certio you open Tester link in the Toolbox, or tap Pair MFT on the schedule grid, scan for the tester and tap it to connect. After that, pressing Save on the MFT-X1 after a test sends the reading to the app, which offers it against the cell you have selected. It is labelled beta because it has been proven on a limited number of testers and firmware versions, and the camera read is always there as the fallback.
Which readings does the Bluetooth link fill in?
Insulation resistance in megohms, continuity readings in ohms (R1+R2, R2 and the ring final r1, rn and r2) and earth fault loop impedance Zs in ohms: those are the readings proven on a real tester. RCD trip times are mapped in the link but not yet verified in the field, so use the camera read for column 28 for now. Before it fills an insulation or resistance cell the app checks the unit of the reading, so a volts record can never land in an ohms column, and anything the link does not recognise is shown to you rather than written anywhere.
Can Certio read the tester screen with the camera instead?
Yes, on the Starter and Pro plans. Select the cell on the schedule of test results, point the phone camera at the MFT-X1 display with the reading stable on screen, and the value is read into that cell for you to confirm. Ze and Zs look identical on the screen, so the app never decides which one a reading is from the picture; the cell you selected decides. The Free plan has no AI features, so readings are typed.
Does it work with older Megger testers like the MFT1741 or MFT1835?
The Bluetooth link is for the MFT-X1 only. Older Megger MFT models use a different radio or none at all, and the beta does not support them. Those testers, and other makes with a readable display, may read by camera on the paid plans, but the camera read has only been tested on the MFT-X1. Certio does not read Kewtech, Metrel or Fluke testers over Bluetooth.
What do I do if the MFT-X1 will not connect?
Check Bluetooth is on in the tester's settings and on the phone, keep the app in the foreground while you capture, and tap Scan for tester again. If a reading arrives but is cut short, disconnect and reconnect so the app can renegotiate the link. If it still will not connect, use the camera read and send a capture from the Tester link screen to support@certio.uk so we can look at it.
Does Certio replace Megger CertSuite?
Not necessarily. CertSuite is Megger's own certificate software, sold separately, and it is the official companion for the MFT-X1. Certio is an independent certificate app that reads the MFT-X1 by camera and, in beta, over Bluetooth; Megger has not endorsed it. If you already pay for CertSuite and it does what you need, there is no reason to change. If you want certificates, quotes and invoices in one phone app for £4.99 or £9.99 a month, Certio is worth a look.
Less typing, same judgement

Down tools at 5. The paperwork's already done.

Certio lays out EICR, EIC, Minor Works and PAT certificates to the BS 7671 model forms and produces branded PDFs. Photograph the board and the schedule drafts itself; point the camera at a Megger MFT-X1 and the reading goes straight in. There's a free plan with no card. Starter is £4.99 a month and Pro £9.99 with unlimited certificates, charged when you sign up.

Get Starter · £4.99/mo →

More on EICR software and AI EICR software.

Sources

  1. IET: BS 7671:2018+A4:2026 Requirements for Electrical Installations (18th Edition) and model forms
  2. BSI: BS EN 61557, electrical safety in low voltage distribution systems, equipment for testing

Checked against these sources on 17 November 2026. This guide is general information for electricians, not legal advice.